Moisture Control

100% Solids, Two-Component Epoxy – No VOC off-gassing, excellent coverage and performance.
Moisture Tolerant – Can be applied on damp or poorly prepared concrete surfaces.
Approved for Potable Water Contact – Safe for environments with water exposure.
Strong Mechanical Properties – High flexural (15,000 psi) and compressive strength (8,000 psi).
LEED v4 Compliant & Low VOC – Contributes to green building certifications (VOC <20 g/L).

Remove dust, dirt, grease, oil, and all other contaminants with proper cleaner/degreaser. Prepare the surface mechanically as per ICRI-CSP2 profile by diamond grinding to ensure removal of laitance, curing agents and sealers. The compressive strength of a newly poured concrete substrate must be at least 25 MPA (3635 psi) after 28 days of cure and at least 1.5 MPA (218 psi) tensile strength. The EF-160 can be applied on concrete that has cured for a minimum of 14 days. For concrete that is between 14-28 days old, the use of our EF-400 deep penetrating primer is required. All cracks, holes and irregularities must be repaired with a crack filler prior to applying the coating.

Ultra-Fast Cure Time – Recoatable in as little as 2–4 hours at 20°C.
100% Solids Epoxy with Low VOC – VOC <20 g/L, no shrinkage or odor.
High Chemical and Abrasion Resistance – Same abrasion loss as EF-160 (0.11g loss/1000 cycles).
Potable Water and Food Contact Approved – Meets CFIA, USDA, LEED v4 standards.
Strong Adhesion & Tensile Strength – Pull-off strength > 363 psi; tensile 6,000 psi.

Remove dust, dirt, grease, oil, and all other contaminants with proper cleaner/degreaser. Prepare the surface mechanically as per ICRI-CSP2 profile by diamond grinding to ensure removal of laitance, curing agents and sealers. The compressive strength of a newly poured concrete substrate must be at least 25 MPA (3635 psi) after 28 days of cure and at least 1.5 MPA (218 psi) tensile strength. The EF-165 can be applied on concrete that has cured for a minimum of 14 days. For concrete that is between 14-28 days old, the use of our AQUAFLOW-400 deep penetrating primer is required. All cracks, holes and irregularities must be repaired with a crack filler prior to applying the coating.

Rapid Curing System – Foot traffic ready in 6–8 hours at room temperature.
High Compressive Strength – 10,000 psi (higher than EF-160 & EF-165).
Potable Water Approved & LEED Compliant – Safe and sustainable (VOC<20 g/L).
Excellent Vapor Barrier – Withstands up to 25 lbs/1000 ft²/24 hrs moisture vapor emission.
Flexible Kit Size (2-Gallon) – Ideal for smaller or segmented application areas.

Remove dust, dirt, grease, oil, and all other contaminants with proper cleaner/degreaser. Prepare the surface mechanically as per ICRI-CSP2 profile by diamond grinding to ensure removal of laitance, curing agents and sealers. The compressive strength of a newly poured concrete substrate must be at least 25 MPA (3635 psi) after 28 days of cure and at least 1.5 MPA (218 psi) tensile strength. The EF-180 can be applied on concrete that has cured for a minimum of 14 days. For concrete that is between 14-28 days old, the use of our AQUAFLOW-400 deep penetrating primer is required. All cracks, holes and irregularities must be repaired with a crack filler prior to applying the coating.